The original
2C-20-310 Ready to Run Brushless Motor.
£34.99

If your pushed for time but must have the ultimate Shock Flier motor now, buy one fully assembled.

Total weight : 20 grams

Application: 3D planes upto 200grams Auw

Max thrust on 2cells: 310 grams 7.2V.
Max Sustained current:
6.8Amps.
No Load current @ 6.6V:
0.3Amps.
No Load RPM/volt:
1880 @ 6V.
Props: 8x4.3-9x4.7.

Bell assembly CNC machined aerospace grade aluminum. Heat treated and polished for scratch and dent resistance. Built in prop adaptor/saver. Deep center boss gives maximum rigidity. Accepts a GWS prop with no modification. Factory jig fitted and bonded magnets. Bonded to a CNC machined polished stainless steel ring.

Stub shaft CNC machined aerospace grade aluminum heat-treated. Factory bonded and wound stator. Two high quality, high-speed double shielded bearing factory press fitted.

Main shaft CNC machined Hardened and ground steel. Eclip groove and screw location flats.

Pre assembled and ready to mount.

Also included Oring prop retainer, New Clamp mount tube.

Connection Solder connection plate fitted as standard.

3C-20-340 Ready to Run Brushless Motor .
£34.99

If your pushed for time but must have the ultimate Shock Flier motor now, buy one fully assembled.

The same great lightweight design as the original 2C-20-310. But optimized for 3Cells and a 8x4.3 prop.

Total weight : 20 grams

Application: 3D planes upto 220grams Auw.

Max thrust on 3cells: 340 grams
@ 11.1V.
Max Sustained current:
5Amps.
No Load current @ 9.9V:
0.3Amps.
No Load RPM/volt:
1209 @ 10.2V.
Props: 8x4.3-9x4.7.

Bell assembly CNC machined aerospace grade aluminum. Heat treated and polished for scratch and dent resistance. Built in prop adaptor/saver. Deep center boss gives maximum rigidity. Accepts a GWS prop with no modification. Factory jig fitted and bonded magnets. Bonded to a CNC machined polished stainless steel ring.

Stub shaft CNC machined aerospace grade aluminum heat-treated. Factory bonded and wound stator. Two high quality, high-speed double shielded bearing factory press fitted.

Main shaft CNC machined Hardened and ground steel. Eclip groove and screw location flats.

Pre assembled and ready to mount.

Also included, Oring prop retainer, New Clamp mount tube.

Connection Solder connection plate fitted as standard.

New lower price
2/3C-20-310 Brushless Motor Kit.
£23.99.

The same great lightweight design as the original 2C&3C-20-310. But in kit form.
Now includes instructions and two spools of wire to construct either the 2cell or 3cell motor, at no extra cost.

Total weight : 20 grams

Application: Only limited by output power.

Max Thrust on 2 cells: 310 grams @ 7.4V.
Max Thrust on 3 cells: 340 grams @ 11.1V.

Instructions Easy step by step color photo instructions.

Bell assembly CNC machined aerospace grade aluminum, heat treated and polished for scratch and dent resistance. Built in prop adaptor/saver. Deep center boss gives maximum rigidity. Accepts a GWS prop with no modification. Pre machined magnet location slots ensure positive accurate magnet location. Bonded to a CNC machined polished stainless steel ring.

Stub shaft CNC machined aerospace grade aluminum heat-treated. Stator pre bonded to stub shaft. Two high quality, high-speed double shielded bearing factory press fitted.

Main shaft CNC machined Hardened and ground steel. eclip groove and screw location flats.

Also included Stator, 15x magnets, thats 3 spare, 2x screws, special eclip, Copper enameled wire, solder connector plate, Oring prop retainer, New Clamp mount tube.

Connection Solder connection plate,or use trailing wires.
 

New lower price .
2/3C-20-310 Stage One Brushless Motor Kit.
£26.99

Total weight : 20 grams.

Application: Only limited by output power.

Max Thrust on 2 cells: 310 grams @ 7.4V.
Max thrust on 3cells: 340 grams @ 11.1V.

Benefits over standard kit The magnets are pre factory fitted and the stator is pre bonded to the stub shaft. All you have to do is wind the stator and assemble. Easy.
Now includes instructions and two spools of wire to construct either the 2cell or 3cell motor, at no extra cost.

Instructions Easy step by step color photo instructions.

Bell assembly CNC machined aerospace grade aluminum, heat treated and polished for scratch and dent resistance. Built in prop adaptor/saver. Deep center boss gives maximum rigidity. Accepts a GWS prop with no modification. Pre factory jig fitted magnets.

Stub shaft CNC machined aerospace grade aluminum heat-treated. Pre bonded stator. Two high quality, high-speed double shielded bearing factory press fitted.

Main shaft CNC machined Hardened and ground steel. eclip groove and screw location flats.

Also included 2x screws, special eclip, Copper enameled wire, solder connection plate, heat shrink tube, Oring prop retainer, New Clamp mount tube.

Connection solder connection plate,or use trailing wires.

New 3C-40-High speed Park fly RTR Brushless Motor.
£38.99

Total weight : 40 grams
Application: High speed models originally using 5x5 props such as jets and delta wings.
Max Sustained current: 12 Amps.
No Load current @ 11.1v: 0.8Amps.
No Load RPM/volt: 1844.
Props: 5x5- 7x5.
recommended Cells: 1250Mah 15C

Bell assembly CNC machined aerospace grade aluminum. Heat treated and polished for scratch and dent resistance. Built in prop adaptor/saver. Deep center boss gives maximum rigidity. Accepts a GWS prop with no modification. Factory jig fitted and bonded magnets. Bonded to a CNC machined polished stainless steel ring.

Stub shaft CNC machined aerospace grade aluminum heat-treated. Factory bonded and wound stator. Two high quality, high-speed double shielded bearing factory press fitted.

Main shaft CNC machined Hardened and ground steel. End boss eliminates the need for an eclip. Screw location flats.

Pre assembled and ready to mount.

Also included Oring prop retainer, New Clamp mount tube.
Connection Solder connection plate fitted as standard.

New 3C-40-3D Park fly
RTR Brushless Motor.
£38.99

Total weight : 40 grams
Application: 3D and Park fly planes to 450 Grams Auw. Ideal for war bird park flyers.
Max thrust 3cells: 640 grams @ 11.1V.
Max Sustained current: 11 Amps.
No Load current @ 11.1v: 0.4Amps.
No Load RPM/volt:
1022 @ 11.1V.
Props: 9x4.7 - 10x4.7
recommended Cells: 1250Mah 15C.

Bell assembly CNC machined aerospace grade aluminum. Heat treated and polished for scratch and dent resistance. Built in prop adaptor/saver. Deep center boss gives maximum rigidity. Accepts a GWS prop with no modification. Factory jig fitted and bonded magnets. Bonded to a CNC machined polished stainless steel ring.

Stub shaft CNC machined aerospace grade aluminum heat-treated. Factory bonded and wound stator. Two high quality, high-speed double shielded bearing factory press fitted.

Main shaft CNC machined Hardened and ground steel. End boss eliminates the need for an eclip. Screw location flats.

Pre assembled and ready to mount.

Also included Oring prop retainer, New Clamp mount tube.
Connection Solder connection plate fitted as standard.

New As reviewed in July 2005 QEFI magazine (3C-38-600).
3C-40-Slow fly Park fly
RTR Brushless Motor.
£38.99

Total weight : 40 grams
Application: Slow fly and Park fly planes to 500 Grams Auw. Ideal for cub and beaver slow flyers for long flights.
Max thrust 3cells: 680 grams @ 11.1V.
Max Sustained current: 9 Amps.
No Load current @ 11.1v: 0.3Amps.
No Load RPM/volt:
890 @ 11.1V.
Props: 9x4.7 - 10x4.7.
recommended Cells: 910Mah 15C.

Bell assembly CNC machined aerospace grade aluminum. Heat treated and polished for scratch and dent resistance. Built in prop adaptor/saver. Deep center boss gives maximum rigidity. Accepts a GWS prop with no modification. Factory jig fitted and bonded magnets. Bonded to a CNC machined polished stainless steel ring.

Stub shaft CNC machined aerospace grade aluminum heat-treated. Factory bonded and wound stator. Two high quality, high-speed double shielded bearing factory press fitted.

Main shaft CNC machined Hardened and ground steel. End boss eliminates the need for an eclip. Screw location flats.

Pre assembled and ready to mount.

Also included Oring prop retainer, New Clamp mount tube.
Connection Solder connection plate fitted as standard.

Park flyer motor
3C-40-DUAL DIY Brushless Motor Kit. 
£30.99

Total weight : 40 grams.
Application: The ideal choice for flyers on a budget or more experienced modelers who are looking for a tailor made motor application.Only limited by output power.
Max thrust on 3cells: 600-700+ grams
on 9x4.7 prop.

Instructions Comprehensive but easy step by step color photo instructions.

Bell assembly CNC machined aerospace grade aluminum, heat treated and polished for scratch and dent resistance. Built in prop adaptor/saver. Deep center boss gives maximum rigidity. Accepts a GWS prop with no modification. Pre machined magnet location slots ensure positive accurate magnet location. Bonded to a CNC machined polished stainless steel ring.

Stub shaft CNC machined aerospace grade aluminum heat-treated. Incorporated shoulder for positive stator location. Two high quality, high-speed double shielded bearing factory press fitted.

Main shaft CNC machined Hardened and ground steel. eclip groove and screw location flats.

Also included Stators, 12x magnets, 2x screws, special eclip, Copper enameled wire,solder connection plate, heat shrink tube, Oring prop retainer, New Clamp mount tube.
Connection Solder connection plate,or use trailing wires.

Out of stock
2C-22-Helicopter RTR Brushless Motor.
£34.99

If your pushed for time but must have the ultimate indoor helicopter motor now, buy one fully assembled.

Total weight : 22 grams.
Max Voltage: 8.4
Max Sustained current: 6Amps.
No Load current @ 7.4V: 1.1Amp.
No Load RPM/volt:
4520 @ 7.4V.

Designed to suit the Piccolo but can be used in almost all indoor helicopters. Long splined shaft to cope with varied shaft lengths. Same foot print as speed 300 motor.

All other specs same as kit below.

Note
 The use of an additional brushless controller is required. We recommend the Jeti 08-3P.

Out of stock
2C-22-Helicopter Brushless Motor Kit.  £27.99

Total weight : 22 grams

Designed to suit the Piccolo but can be used in almost all indoor helicopters.

Instructions Easy step by step color photo instructions.

Bell assembly CNC machined aerospace grade aluminum, heat treated and polished for scratch and dent resistance. Uses same bell as shock flyer version to allow interchangeability. Deep center boss gives maximum rigidity. Slotted grub screws for easy assembly with minimum tools.

Mounting plate CNC machined from aerospace grade aluminum. Two M2.5 threaded holes for direct mounting, hole for bottom cable exiting. Uses slotted grub screws to attach to stub shaft to allow for disassembly and rewinding.

Stub shaft CNC machined aerospace grade aluminum heat-treated. Two high quality, high-speed double shielded bearing factory press fitted.

Main shaft CNC machined Hardened and ground steel. Splined to guarantee against slippage of pinion gear.eclip groove and screw location flats.

Also included 2x mounting screws, special eclip, Copper enameled wire, heat shrink tube, mount.